OBC 2006 › Division B
7.5.8.4.
Version 0 — in force 31 December 2006
This looks wrong
Tell us what is wrong and we will verify & correct our mapping.
- Edition
- OBC_2006
- Division
- B
- Provision
- 7.5.8.4.
- Version
- v0
(1) This Regulation comes into force on December 31, 2006.
Read directly from the regulation's own commencement section.
O. Reg. 350/06 · commencement 2.2.1.1(1)
This version stayed in force until the next one commenced. What follows is that next version’s commencement — the event that ended this one.
240. (1) Subject to subsections (2), (3), (4), (5), (6) and (7), this Regulation comes into force on the later of January 1, 2010 and the day this Regulation is filed.
Read directly from the regulation's own commencement section.
O. Reg. 503/09 · commencement 240(1)
This looks wrong
Tell us what is wrong and we will verify & correct our mapping.
- Edition
- OBC_2006
- Division
- B
- Provision
- 7.5.8.4.
- Version
- v0
(1) This Regulation comes into force on December 31, 2006.
Read directly from the regulation's own commencement section.
O. Reg. 350/06 · commencement 2.2.1.1(1)
This version stayed in force until the next one commenced. What follows is that next version’s commencement — the event that ended this one.
240. (1) Subject to subsections (2), (3), (4), (5), (6) and (7), this Regulation comes into force on the later of January 1, 2010 and the day this Regulation is filed.
Read directly from the regulation's own commencement section.
O. Reg. 503/09 · commencement 240(1)
Provenance
OBC 1997 · renumbered from 7.5.7.3. — Pro
Base · O. Reg. 350/06 · ext← current
Original — base regulation
O. Reg. 503/09, cl. 109 · ext v1 →
In force 2010-01-01
Next: O. Reg. 503/09, cl. 109 · ext (not in force until 2010-01-01) v1 →
OBC 2012 · continues as 7.5.8.4. — Pro
7.5.8.4. — Vent Stacks, or Stack Vents
Comparing versions
Changed text stands out · unchanged is dimmed
v0 base
Earlier · viewing · 2006-12-31(1) A vent stack, or stack vent shall be sized in accordance with Table 7.5.8.4. based on,
(a) the length of the vent stack or stack vent, and
(b) the total hydraulic load that is drained to the lowest section of soil or waste stack or stacks served by the vent pipe, plus any additional vent loads connected to the vent stack or stack vent.
(2) For the purposes of Table 7.5.8.4., the length of a stack vent or vent stack shall be its developed length from its lower end to open air.
(3) The minimum size of vent stack or stack vent shall be one-half the size of the soil or waste stack at its base.
(4) A stack vent serving a wet vent stack that is over 4 storeys high shall extend the full size of the wet vent to open air.
(5) Every sanitary building drain shall be provided with at least one vent that is not less than 3 in. in size.
v1 O. Reg. 503/09
Later · 2010-01-01(1) A vent stack, or stack vent shall be sized in accordance with Table 7.5.8.4. based on,
(a) the length of the vent stack or stack vent, and
(b) the total hydraulic load that is drained to the lowest section of soil or waste stack or stacks served by the vent pipe, plus any additional vent loads connected to the vent stack or stack vent.
(2) For the purposes of Table 7.5.8.4., the length of a stack vent or vent stack shall be its developed length from its lower end to open air.
(3) The minimum size of vent stack or stack vent shall be one-half the size of the soil or waste stack at its base.
(4) A stack vent serving a wet vent stack that is over 4 storeys high shall extend the full size of the wet vent to open air.
(5) Every sanitary building drain shall be provided with at least one vent that is not less than 3 in. in size.
Provenance
OBC 1997 · renumbered from 7.5.7.3. — Pro
Base · O. Reg. 350/06 · ext← current
Original — base regulation
O. Reg. 503/09, cl. 109 · ext v1 →
In force 2010-01-01 comparing ×
Next: O. Reg. 503/09, cl. 109 · ext (not in force until 2010-01-01) v1 →
OBC 2012 · continues as 7.5.8.4. — Pro