OBC 2006 › Division B
9.29.5.9.
Version 1 — in force 1 January 2010
This looks wrong
Tell us what is wrong and we will verify & correct our mapping.
- Edition
- OBC_2006
- Division
- B
- Provision
- 9.29.5.9.
- Version
- v1
240. (1) Subject to subsections (2), (3), (4), (5), (6) and (7), this Regulation comes into force on the later of January 1, 2010 and the day this Regulation is filed.
Read directly from the regulation's own commencement section.
O. Reg. 503/09 · commencement 240(1)
This version stayed in force until the next edition replaced it. What follows is that edition’s base regulation’s commencement — the takeover that ended this one.
(1) Subject to Sentences (2) and (3), this Regulation comes into force on January 1, 2014.
Read directly from the regulation's own commencement section.
O. Reg. 332/12 · commencement 4.4.1.1(1)
This looks wrong
Tell us what is wrong and we will verify & correct our mapping.
- Edition
- OBC_2006
- Division
- B
- Provision
- 9.29.5.9.
- Version
- v1
240. (1) Subject to subsections (2), (3), (4), (5), (6) and (7), this Regulation comes into force on the later of January 1, 2010 and the day this Regulation is filed.
Read directly from the regulation's own commencement section.
O. Reg. 503/09 · commencement 240(1)
This version stayed in force until the next edition replaced it. What follows is that edition’s base regulation’s commencement — the takeover that ended this one.
(1) Subject to Sentences (2) and (3), this Regulation comes into force on January 1, 2014.
Read directly from the regulation's own commencement section.
O. Reg. 332/12 · commencement 4.4.1.1(1)
Provenance
OBC 1997 · continues from 9.29.5.9. — Pro
Base · O. Reg. 350/06 · ext v0 →
O. Reg. 503/09, cl. 186 · ext ← current
In force 2010-01-01
OBC 2012 · continues as 9.29.5.9. — Pro
9.29.5.9. — Spacing of Screws
Comparing versions
Changed text stands out · unchanged is dimmed
v0 base
Earlier · 2006-12-31(1) For single-layer application on a ceiling, screws shall be spaced not more than 300 mm o.c. on ceiling supports.
(2) Where the ceiling sheets are supported by the wall sheets around the perimeter of the ceiling, this support may be considered as equivalent to screwing at this location.
(3) Except as required by Sentence (4), for single-layer application on walls, screws shall be spaced,
(a) not more than 300 mm o.c. on vertical wall supports where the supports are more than 400 mm o.c., or
(b) not more than 400 mm o.c. on vertical wall supports where the supports are not more than 400 mm o.c.
(4) Except as required by Sentence (5), for single-layer application on walls, where gypsum board is required to provide bracing, lateral support or fire protection, screws shall be spaced not more than 300 mm o.c. on,
(a) vertical wall supports, and
(b) top and bottom plates.
(5) Where a fire-resistance rating is determined based on Supplementary Standard SB-3, Sentence (4) need not apply for the purpose of fire protection.
(6) Screws shall be located not less than 10 mm from the side or edge of the board.
(7) Screws shall be driven so that the heads do not puncture the paper.
v1 O. Reg. 503/09
Later · viewing · 2010-01-01(1) For single-layer application on a ceiling, screws shall be spaced not more than 300 mm o.c. on ceiling supports.
(2) Where the ceiling sheets are supported by the wall sheets around the perimeter of the ceiling, this support may be considered as equivalent to screwing at this location.
(3) Except as required by Sentence (4), for single-layer application on walls, screws shall be spaced,
(a) not more than 300 mm o.c. on vertical wall supports where the supports are more than 400 mm o.c., or
(b) not more than 400 mm o.c. on vertical wall supports where the supports are not more than 400 mm o.c.
(4) Except as required by Sentence (5), for single-layer application on walls, where gypsum board is required to provide bracing, lateral support or fire protection, screws shall be spaced not more than 300 mm o.c. on,
(a) vertical wall supports, and
(b) top and bottom plates.
(5) Where a fire-resistance rating is determined based on Table 1 of Supplementary Standard SB-3, Sentence (4) need not apply for the purpose of fire protection.
(6) Screws shall be located not less than 10 mm from the side or edge of the board.
(7) Screws shall be driven so that the heads do not puncture the paper.
Provenance
OBC 1997 · continues from 9.29.5.9. — Pro
Base · O. Reg. 350/06 · ext v0 → comparing ×
O. Reg. 503/09, cl. 186 · ext ← current
In force 2010-01-01
OBC 2012 · continues as 9.29.5.9. — Pro