OBC 2006 › Division B
9.27.9.
Version 0 — in force 31 December 2006
This looks wrong
Tell us what is wrong and we will verify & correct our mapping.
- Edition
- OBC_2006
- Division
- B
- Provision
- 9.27.9.
- Version
- v0
(1) This Regulation comes into force on December 31, 2006.
Read directly from the regulation's own commencement section.
O. Reg. 350/06 · commencement 2.2.1.1(1)
This version stayed in force until the next edition replaced it. What follows is that edition’s base regulation’s commencement — the takeover that ended this one.
(1) Subject to Sentences (2) and (3), this Regulation comes into force on January 1, 2014.
Read directly from the regulation's own commencement section.
O. Reg. 332/12 · commencement 4.4.1.1(1)
This looks wrong
Tell us what is wrong and we will verify & correct our mapping.
- Edition
- OBC_2006
- Division
- B
- Provision
- 9.27.9.
- Version
- v0
(1) This Regulation comes into force on December 31, 2006.
Read directly from the regulation's own commencement section.
O. Reg. 350/06 · commencement 2.2.1.1(1)
This version stayed in force until the next edition replaced it. What follows is that edition’s base regulation’s commencement — the takeover that ended this one.
(1) Subject to Sentences (2) and (3), this Regulation comes into force on January 1, 2014.
Read directly from the regulation's own commencement section.
O. Reg. 332/12 · commencement 4.4.1.1(1)
Provenance
OBC 1997 · continues from 9.27.9. — Pro
Base · O. Reg. 350/06 · ext← current
Original — base regulation
OBC 2012 · renumbered to 9.27.8. — Pro
9.27.9. — Plywood
Content not available for this version.
9.27.9.1. — Material Standards
(1) Plywood cladding shall be exterior type conforming to,
(a) CSA O115-M, “Hardwood and Decorative Plywood”,
(b) CSA O121-M, “Douglas Fir Plywood”,
(c) CSA O151, “Canadian Softwood Plywood”, or
(d) CSA O153-M, “Poplar Plywood”.
Text · e-Laws consolidated snapshot
9.27.9.2. — Thickness
(1) Plywood cladding shall be not less than 6 mm thick when applied directly to sheathing.
(2) When applied directly to framing or over furring strips, plywood cladding thickness shall conform to Table 9.27.9.2.
(3) The thickness of grooved or textured plywood shall be measured at the point of least thickness.
Text · e-Laws consolidated snapshot
Column 1 | Column 2 | Column 3 |
Spacing of Supports, mm | Minimum Thickness, mm, where Face Grain Parallel to Supports | Minimum Thickness, mm, where Face Grain at Right Angles to Supports |
400 | 8 | 6 |
600 | 11 | 8 |
9.27.9.3. — Edge Treatment
(1) The edges of plywood cladding shall be treated with a suitable paint or sealer.
Text · e-Laws consolidated snapshot
9.27.9.4. — Panel Cladding
(1) Plywood applied in panels shall have all edges supported.
(2) Not less than a 2 mm gap shall be provided between panels referred to in Sentence (1).
(3) Vertical joints in cladding referred to in Sentence (1) shall be protected with batten strips or caulking when the plywood joints are not matched.
(4) Horizontal joints in cladding referred to in Sentence (1) shall be lapped not less than 25 mm or shall be suitably flashed.
Text · e-Laws consolidated snapshot
9.27.9.5. — Lapped Strip Siding
(1) Plywood applied in horizontal lapped strips shall have not less than a 2 mm gap provided at the butted ends, which shall be caulked.
(2) The horizontal joints of siding described in Sentence (1) shall be lapped not less than 25 mm.
(3) Wedges shall be inserted under all vertical butt joints and at all corners when horizontal lapped plywood is applied without sheathing.
Text · e-Laws consolidated snapshot
Provenance
OBC 1997 · continues from 9.27.9. — Pro
Base · O. Reg. 350/06 · ext← current
Original — base regulation
OBC 2012 · renumbered to 9.27.8. — Pro