OBC 2006 › Division B
9.27.11.
Version 0 — in force 31 December 2006
This looks wrong
Tell us what is wrong and we will verify & correct our mapping.
- Edition
- OBC_2006
- Division
- B
- Provision
- 9.27.11.
- Version
- v0
(1) This Regulation comes into force on December 31, 2006.
Read directly from the regulation's own commencement section.
O. Reg. 350/06 · commencement 2.2.1.1(1)
This version stayed in force until the next edition replaced it. What follows is that edition’s base regulation’s commencement — the takeover that ended this one.
(1) Subject to Sentences (2) and (3), this Regulation comes into force on January 1, 2014.
Read directly from the regulation's own commencement section.
O. Reg. 332/12 · commencement 4.4.1.1(1)
This looks wrong
Tell us what is wrong and we will verify & correct our mapping.
- Edition
- OBC_2006
- Division
- B
- Provision
- 9.27.11.
- Version
- v0
(1) This Regulation comes into force on December 31, 2006.
Read directly from the regulation's own commencement section.
O. Reg. 350/06 · commencement 2.2.1.1(1)
This version stayed in force until the next edition replaced it. What follows is that edition’s base regulation’s commencement — the takeover that ended this one.
(1) Subject to Sentences (2) and (3), this Regulation comes into force on January 1, 2014.
Read directly from the regulation's own commencement section.
O. Reg. 332/12 · commencement 4.4.1.1(1)
Provenance
OBC 1997 · continues from 9.27.11. — Pro
Base · O. Reg. 350/06 · ext← current
Original — base regulation
OBC 2012 · renumbered to 9.27.10. — Pro
9.27.11. — OSB and Waferboard
Content not available for this version.
9.27.11.1. — Material Standard
(1) OSB and waferboard cladding shall conform to CSA O437.0, “OSB and Waferboard”.
Text · e-Laws consolidated snapshot
9.27.11.2. — Thickness
(1) OSB conforming to O-2 grade shall be not less than 6.0 mm thick where applied directly to sheathing.
(2) OSB conforming to O-2 grade applied directly to framing or over furring strips, shall conform to the thickness shown for plywood in Table 9.27.9.2.
(3) OSB conforming to O-1 grade and waferboard conforming to R-1 grade shall be not less than 7.9 mm thick where applied directly to sheathing.
(4) Where applied directly to framing or over furring strips, OSB conforming to O-1 grade and waferboard conforming to R-1 grade shall be not less than,
(a) 9.5 mm thick on supports spaced not more than 400 mm o.c., and
(b) 12.7 mm thick on supports spaced not more than 600 mm o.c.
Text · e-Laws consolidated snapshot
9.27.11.3. — Panel Cladding
(1) OSB and waferboard applied in panels shall have all edges supported and treated with a primer or sealer.
(2) Not less than a 3 mm gap shall be provided between sheets in cladding described in Sentence (1).
(3) Vertical joints in cladding described in Sentence (1) shall be protected with batten strips or caulking when the OSB and waferboard joints are not matched.
(4) Horizontal joints in cladding described in Sentence (1) shall be lapped not less than 25 mm or shall be suitably flashed.
Text · e-Laws consolidated snapshot
9.27.11.4. — Clearance
(1) At least a 3 mm clearance shall be provided between OSB and waferboard cladding and door or window frames.
Text · e-Laws consolidated snapshot
Provenance
OBC 1997 · continues from 9.27.11. — Pro
Base · O. Reg. 350/06 · ext← current
Original — base regulation
OBC 2012 · renumbered to 9.27.10. — Pro